Be In The Know

rss logo RSS Feed
Buying | 65 Posts
Real Estate News | 43 Posts
Selling | 45 Posts
October
13

Before anyone starts development in a floodplain on unincorporated Boone County land, the county's posted zoning code requires a development permit from the zoning enforcement officer. The floodplain is the land a base flood would cover, meaning a flood with a one percent chance of being equaled or exceeded in any given year, as drawn on the FEMA map for the county dated February 18, 2011. If you are weighing homes for sale in Boone County on acreage or outside a city or village, that rule decides what you can add, raise, fill or rebuild near a creek or the Kishwaukee River. Gambino Realtors has worked in the Rockford area since 1923. This guide sticks to the county's own code pages, its Unified Development Ordinance and FEMA's pages.

Which Land And Which Text

The county's Unified Development Ordinance says it applies to all land, uses and structures within the unincorporated limits of Boone County. It also governs a property that has an annexation agreement with a municipality more than 1.5 miles away. Land inside a city or village sits outside that reach. The county's building page puts the same point from the other direction: if an address is being rejected in the online permit system, it may not be located within the county's jurisdiction. For land inside Belvidere, read the Belvidere flood zones guide instead of this one.

Two county documents matter here, and they do not line up neatly. The first is Section 3.13 of the zoning ordinance, titled Floodplain Overlay District. The County Board adopted it in its current form by Ordinance 11-04 on January 19, 2011, and it is the section the county's posted code on Municode still shows. That code is current through Ordinance 24-08, adopted April 26, 2024. The county's local amendments to the residential building code refer to a floodplain ordinance as well. In the table of design criteria, the line for flood hazard reads "See Floodplain Ordinance."

The second document is newer. The Planning Department page says the final Boone County Unified Development Ordinance and Zoning Map were adopted June 18, 2026. The ordinance PDF posted by the county is dated June 23, 2026, and it calls itself Appendix A of the Boone County Code of Ordinances, the same appendix that held the older zoning ordinance. A text search of that PDF finds no floodplain overlay district and no floodplain development permit section. It does contain a Special Flood Hazard Area review for subdivisions, definitions of floodplain, floodway and flood fringe, and several limits that keep floodplain land out of required open space and land donations. The effective date line in the PDF is still a placeholder that reads "MONTH DATE, 2026."

So here is the honest position. The pages the county has posted do not say whether the 2011 floodplain section carries forward unchanged, has been replaced, or is handled somewhere else. This guide reports the 2011 text because it is the only floodplain permit text the county has published that a reader can open, and it reports what the new ordinance does say. Before you rely on either, ask the Planning Department at 815.547.4770 which text governs your parcel and ask for the page. The new ordinance also has a transition rule. A zoning certificate or building permit issued before the effective date may be completed if construction began within six months after it was issued.

Floodplain permits are also separate from the county's stormwater work. The Storm Water and Pollution Control page describes a program of pollution controls for the Belvidere and Boone County area, including construction site storm water runoff control and post construction storm water management in new development and redevelopment. The floodplain permit is a different permit with its own application.

The new ordinance does add two general triggers that can apply to a floodplain parcel without saying the word flood. Site plan review is required for any development that requires stormwater management or the grading of land. Agricultural land and buildings are excepted to the extent state law authorizes. A zoning certificate, the basic zoning approval, must be approved, approved with conditions or denied within 30 days of a complete application.

What Counts As Floodplain, What Counts As Development, And What The Permit Asks For

The 2011 section defines the floodplain and the special flood hazard area as the same thing. They are the lands subject to inundation by the base flood. The streams it names are the Kishwaukee River and the North Kinnikinnick, South Kinnikinnick, Beaver, Mosquito, Picasaw, Meander, Mud and Coon Creeks. Their floodplains are generally identified on the panels of the countywide Flood Insurance Rate Map prepared by FEMA and dated February 18, 2011. The definition also takes in areas of known flooding that the community has identified.

The district boundaries follow the 100-year flood profiles in the Flood Insurance Study of Boone County dated February 18, 2011, together with the soil survey for the county. The floodway is the portion required to store and convey the base flood. The flood fringe is the portion outside it. The new ordinance carries the same split in its definitions. It describes the floodplain as including both the floodway and the flood fringe.

The protection standard is the base flood, and the number that matters for a building is the flood protection elevation. That is the elevation of the base flood plus one foot, a margin the code calls freeboard. For the named streams, the base flood elevation comes from the 100-year profiles in the 2011 study. Where a floodplain is mapped as an AH or AO zone, the elevation or depth is the one on the countywide map. For other mapped A zones, the code uses the data available from federal, state or other sources, and if none exists the applicant pays for an engineering study.

The same section gives a landowner a way to disagree with the map, and it puts the cost on the person disagreeing. Whoever disputes the data must finance a detailed engineering study and submit it to FEMA and to the Illinois Department of Natural Resources Office of Water Resources for approval before development of the site. The code also recognizes a survey. Land shown by survey data to be higher than the current base flood elevation, and not filled after the date of the site's first flood insurance rate map, is not in the floodplain for purposes of the section. The reverse also holds. Land shown to be below the base flood elevation and hydraulically connected is subject to the section even if the current map does not show it.

Development is defined broadly, and the definition is why a small project can need a permit. It covers demolition, construction, reconstruction, repair, placement of a building and any structural alteration. It covers a substantial improvement, installing a manufactured home, and putting a travel trailer on a site for more than 180 days per year. It covers utilities, roads, bridges and culverts, and it covers levees, dams, walls and fences. It covers drilling, mining, filling, dredging, grading, excavating and paving. It covers storing materials, including gas and liquid storage tanks, and any activity that might change the direction, height or velocity of flood or surface waters. Routine maintenance of existing buildings, resurfacing roads, gardening and plowing are excluded, as long as they do not involve filling, grading or building levees.

The section also limits what may be done in the district at all, whatever the underlying zoning says. The permitted uses are agriculture and row crop production, wholesale nursery stock, orchards and vineyards, land and water conservation practices, artificial lakes of five acres or less, public parks and playgrounds, towers under 200 feet, a landing area for five or fewer ultra-light air vehicles, and accessory uses and buildings. Other uses need a special use, among them larger lakes and marinas, earth materials extraction, airports, outdoor commercial recreation, seasonal tourist attractions and a public camp. Setbacks come from the underlying district. Maximum height is two and one-half stories or 30 feet, whichever is less. The list does not name a house, so a buyer who wants to build new on mapped land should ask the county how the section treats it.

The permit itself is short to describe. No person or body not exempted by law may commence development in the floodplain without a development permit from the zoning enforcement officer, and the officer may not issue it if the proposal does not meet the section. The application must include scaled drawings of the site with property line dimensions, existing grade elevations and every change in grade from excavation or filling, and the location and dimensions of all buildings and additions. It must give the elevation of the lowest floor, basement included, of any proposed building covered by the building standards. It must also include the cost of the project as estimated by a licensed engineer or architect, though a signed contractor estimate may meet that requirement.

The officer then compares the site elevation to the base flood elevation and keeps documentation of the existing ground elevation. The officer must collect copies of all other federal, state and local permits, approvals or permit-not-required letters, and does not issue the floodplain permit until they have all been obtained. Fees are set by the County Board. The pages read for this guide give no fee figure. When the work is finished, the owner applies for an occupancy permit. The code makes it unlawful to use or occupy a building or development site in the special flood hazard area without one, and it requires an as-built elevation certificate prepared by a registered land surveyor before the occupancy certificate is issued.

Separate from the floodplain permit, the Building and Zoning Department takes building permit applications for unincorporated Boone County through the online Cloudpermit system. Its page says that most structures require site plan approval from the Health Department before the building permit is released, and that a property inside a subdivision may need approvals from the association as well. The guide to buying land in Boone County covers the well and septic side of that process.

What A Building In The Floodplain Has To Meet, And What To Check Before You Buy

The building standards in the 2011 section apply in defined situations, and they are cumulative over the life of a building. They apply to a new building or the placement of one. They apply to an alteration or addition to an existing building valued at more than one thousand dollars or 70 square feet. They apply to a substantial improvement, which means work that equals or exceeds 50 percent of the structure's market value before the work starts or increases the floor area by more than 20 percent. They apply to repairs to a substantially damaged building, which means damage that equals or exceeds 50 percent of market value regardless of the repair work actually done, and volunteer labor and materials count toward the figure. They apply to installing a manufactured home on a new site, to a travel trailer or recreational vehicle on a site more than 180 days per year, and to a repetitive loss, which is flood damage on two separate occasions in ten years where repairs each time equaled or exceeded 25 percent of market value. When a building is substantially improved or substantially damaged, the whole structure must meet the standards, not only the new part.

There are three ways to meet the standard for a residential or non-residential building. The first is permanent land fill. The lowest floor, basement included, must be at or above the flood protection elevation. The fill goes down in layers no greater than six inches before compaction. It extends at least ten feet beyond the foundation before sloping below the flood protection elevation. It must be protected against erosion and scour, it must be rock or soil without debris, and it may not adversely affect drainage from or onto neighboring properties.

The second way is to raise the building on stilts, piles, walls, a crawlspace or another foundation that is permanently open to flood waters. The lowest floor and all electrical, heating, ventilating, plumbing and air conditioning equipment and utility meters must be at or above the flood protection elevation. If walls enclose space below that elevation, the design must let flood water enter and leave automatically, either by an engineer's certification or by at least two permanent openings with one on each wall and no more than one foot above grade. The openings must total at least one square inch of net area for every square foot of enclosed area. The space below may be used solely for parking or building access and may not later be modified or occupied as habitable space.

The third way is a crawlspace below the flood protection elevation, under a stricter list. The building must be anchored against flotation, collapse and lateral movement. The interior grade of the crawlspace may be no more than two feet below the lowest adjacent exterior grade. The interior height may not exceed four feet at any point. It needs openings that equalize pressure, a drainage system that clears flood water within a reasonable period, materials resistant to flood damage below the flood protection elevation, and utility systems placed above it.

A non-residential building may be dry flood-proofed instead of raised, but only if a licensed professional engineer or architect certifies it. Below the flood protection elevation the structure must be watertight and able to resist the base flood. The measures must work without human intervention and without an outside source of electricity. Levees, berms and flood walls do not count as flood-proofing. The flood-proofing option is written for non-residential buildings only.

Here is a concrete case. Suppose a parcel touches one of the named creeks and the owner wants a detached garage. The code gives a path for a garage or shed ancillary to an existing residential use, and the path has conditions. The structure must be non-habitable and used only to store vehicles and tools, and it cannot later be converted to another use. It must sit on a single family lot as an accessory to an existing principal structure on the same lot. It must be outside the floodway or have the appropriate state and federal permits. Below the base flood elevation it must be built of materials not susceptible to flood damage, and all utilities must sit above the flood protection elevation. It needs at least one permanent opening on each wall not more than one foot above grade, with one square inch of opening for every square foot of floor area. It must be anchored against flotation and overturning, flammable and toxic materials must be stored above the flood protection elevation, and the owner must be advised of the flood insurance implications.

Inside a floodway, and in any floodplain where no floodway has been mapped, the rule is stricter. No development is allowed that, combined with existing and anticipated development, causes any increase in flood heights or velocities or threat to public health and safety. The code lists activities that meet that test under the state's statewide permits, such as underground utility lines, wells or septic tanks that do not cross a stream, sidewalks, driveways and patios, properly anchored open structures like carports, and the raising of an existing building without changing its outside dimensions or placing fill. Each comes with its own conditions, and the minor activities in that group cannot involve fill or a positive change in grade.

Other standards cover what is stored and what is buried. Chemicals, explosives, buoyant materials, flammable liquids and pollutants may not be placed below the flood protection elevation unless they are in a flood-proofed, anchored tank certified by an engineer or in a flood-proofed building. New and replacement on-site sanitary sewer lines and waste disposal systems must be located and built to avoid impairment or contamination during flooding, and manholes or openings below the flood protection elevation must be watertight. That standard reaches septic systems as well.

The applicant goes to the zoning board of appeals, which makes a recommendation to the County Board. The applicant has to show that the development cannot be located outside the floodplain, that an exceptional hardship would result without the variance, that the relief is the minimum necessary, that there is no additional threat to public health or safety and no additional public expense, that the circumstances are unique, and that all other state and federal permits have been obtained. The zoning enforcement officer must also notify the applicant in writing that a variance from the building protection standards will increase flood insurance premium rates, up to twenty-five dollars per hundred dollars of coverage, and that the applicant proceeds with knowledge of the risk.

On penalties, the 2011 section treats failure to obtain a permit, or failure to meet its conditions, as a violation subject to the penalties in section 2.5.9 of the older zoning ordinance. The pages read for this guide do not give a figure from that section that could be confirmed. The new ordinance's general enforcement rule is a fine of five hundred dollars for each violation, with each day a separate offense, and the owner may be held responsible for the county's legal expenses. The 2011 definitions also say a structure or development without the required federal, state or local permits and elevation certification is presumed to be in violation until the documentation is provided. Whichever text governs, a buyer should ask what permits exist for work already done on the parcel.

What should a buyer check? Start with the map. FEMA's pages explain that a flood insurance requirement applies if you own a home in a Special Flood Hazard Area and have a government-backed mortgage, and that some banks require flood insurance even outside a high-risk zone. Zones A, AE, AH, AO, AR and A99 are the high-risk zones. Building policies cover up to 250,000 dollars of damage and contents policies up to 100,000 dollars, and coverage goes into effect 30 days after purchase unless the policy is bought while making, increasing, extending or renewing a mortgage.

Next, ask for paper. The county's floodplain section directs the zoning enforcement officer to keep a record of the as-built elevation of the lowest floor or the flood-proof certificate, and to keep base flood data, floodplain maps, copies of permits and compliance documents available for public inspection. FEMA says that even outside the highest-risk zones it is worth checking whether a property has an elevation certificate on file. An elevation certificate shows how high a building sits compared with how high local floodwaters are expected to get. Then read the seller's side. The Illinois disclosure report asks the seller whether the seller currently has flood hazard insurance, whether the seller is aware of flooding or recurring leakage in the crawl space or basement, and whether the seller is aware that the property is located in a floodplain. The form defines aware as actual notice or actual knowledge without any specific investigation or inquiry, so it records what the seller knows. The guide to the Illinois seller disclosure report walks through the form.

Bottom Line

Boone County's published floodplain permit text, Section 3.13 of the zoning code, says no development in the floodplain starts without a development permit, and the permit is gated on every other federal, state and local approval. Building standards follow the flood protection elevation, which is the base flood plus one foot, and they reach any substantial improvement or substantial damage over the life of a building. The new Unified Development Ordinance adopted June 18, 2026 does not repeat that section in the PDF the county posted, and the pages do not say which text controls, so confirm it with the Planning Department before you buy, build or fill. If you are comparing homes for sale in Boone County outside the cities and villages, put three questions to the county for each parcel. Is any part of it in the mapped floodplain or a known flooding area? What permits and as-built elevation records are on file? Which ordinance text applies today? For everything else we have written about the area, the Illinois Real Estate Guide lists every article.

The questions below are the ones a reader of the county's code is likely to want settled before calling the county.

Frequently Asked Questions

Does the Boone County floodplain permit apply inside a city or village?

The county's Unified Development Ordinance says it applies to land, uses and structures within the unincorporated limits of Boone County, plus properties with an annexation agreement with a municipality more than 1.5 miles away. Land inside a city or village is outside that reach, so the municipality's own code is the place to look. The county building page adds that if an address is rejected in its permit system, it may not be in the county's jurisdiction. The Planning Department at 815.547.4770 can say which side of the line a parcel is on.

Who issues a floodplain development permit in unincorporated Boone County?

Under Section 3.13 of the county's posted zoning code, the zoning enforcement officer issues it, and the officer may not issue it if the proposed development does not meet the section. The officer also has to collect copies of the other federal, state and local permits, approvals or permit-not-required letters, and does not issue the floodplain permit until all of them have been obtained. Fees are set by the County Board, and the pages read for this guide do not state a figure.

What counts as development in a Boone County floodplain?

The definition covers demolition, construction, reconstruction, repair, placement of a building and structural alteration. It also covers substantial improvements, manufactured homes, utilities, roads, bridges, culverts, levees, dams, walls, fences, filling, grading, excavating, paving and storing materials such as fuel tanks. Routine maintenance of existing buildings, resurfacing roads, gardening and plowing are excluded as long as they do not involve filling, grading or building levees. A small project can still need a permit, so ask before starting.

What if my land is higher than the flood map shows?

The code lets the zoning enforcement officer compare the site elevation to the base flood elevation. Land shown by survey data to be higher than the current base flood elevation, and not filled after the site's first flood insurance rate map, is not in the floodplain for purposes of the section. If you dispute the base flood data itself, you pay for the detailed engineering study and submit it to FEMA and the Illinois Department of Natural Resources Office of Water Resources for approval before development.

When does a house addition have to meet the flood building standards?

The standards apply to an addition or alteration valued at more than one thousand dollars or 70 square feet, and to any substantial improvement. A substantial improvement is work that equals or exceeds 50 percent of the structure's market value before the work starts or increases the floor area by more than 20 percent, figured cumulatively over the life of the building. When a building is substantially improved, the existing structure and the addition must both meet the standards, and the lowest floor must sit at or above the flood protection elevation unless another method in the code is used.

Which ordinance text controls now that the county adopted a new UDO?

The published pages do not settle it. The county's posted code on Municode, current through April 26, 2024, still holds the 2011 Floodplain Overlay District section. The Planning Department says the final Unified Development Ordinance was adopted June 18, 2026, and the PDF dated June 23, 2026 has no floodplain overlay district or floodplain permit section and shows a placeholder effective date. Ask the Planning Department at 815.547.4770 which text governs your parcel and ask for a copy of it.

Will a buyer be told if a property is in a floodplain?

The Illinois seller disclosure report asks whether the seller is aware that the property is located in a floodplain, whether the seller is aware of flooding or recurring leakage in the crawl space or basement, and whether the seller currently has flood hazard insurance. The form defines aware as actual notice or actual knowledge without any specific investigation or inquiry. A buyer should still read the FEMA map and ask the county what permits and elevation records are on file, because the report covers only what the seller knows.

Login to My Homefinder