Be In The Know

rss logo RSS Feed
Buying | 65 Posts
Real Estate News | 43 Posts
Selling | 45 Posts
October
13

A fence, a shed, a pool, a hot tub or a deck inside the City of Byron needs a building permit before work starts, and the city's fee sheet prices each one on its own line. A fence, a deck and an above-ground pool are each listed at eighty dollars. An in-ground pool is listed at one hundred seventy-five dollars. A shed over 100 square feet is priced at twenty-five cents a square foot, with a fifty dollar minimum.

If you are comparing homes for sale in Byron, the yard is part of what you are buying. This guide covers what the city requires, the measurements printed on its own application forms, and what changes when an address sits outside the city limits in unincorporated Ogle County. Gambino Realtors is based in Rockford and has been in business since 1923. Everything below comes from pages the City of Byron and Ogle County publish. It is not legal advice, and only the city's building inspector or the county office can confirm how a rule applies to a particular lot.

What the City of Byron requires, and how the application works

The City of Byron says on its Building Permit Requirements page that it "requires that a building permit be obtained before starting any construction project." The page then lists the common items. Fences, decks and patios, pools or hot tubs, sheds or outbuildings and garages are all on that list. So are new construction, additions, demolition, re-roofing, solar panels, electric service upgrades, and structural remodeling.

Two entries on the list are easy to skim past. Re-roofing needs a permit in Byron. So does replacing a door or window when the size of the opening changes, which the city lists as its own item.

Permits come from Byron City Hall at 232 W Second Street, or from the city's website, where each type of project has its own downloadable form. There are separate forms for a fence, a deck, a shed or detached garage, and a swimming pool or hot tub, among others. The office is open Monday through Friday from 8 am to 4 pm, and the building inspector's line is 815-677-0516.

The city asks for three things with an application. The first is the completed form, which includes a declared value for the project. The second is a set of plans with enough detail and accurate dimensions that a tradesperson could build the project without asking for more information. The third is an up-to-date survey or lot drawing that shows where the project will sit.

The survey requirement applies directly to the projects this guide covers. The city says you need a survey or site plan whenever the project goes outside the footprint of the home, and it names a deck, a garage, a bay window, a roof overhang and a shed as examples. It also asks for the distances from existing and proposed structures to the adjacent lot lines, and it gives the reason in one phrase: those numbers are needed for zoning purposes. In other words, a drawing of the shed alone does not answer the question the city is asking. The question is where the shed sits relative to the lines.

That is also why the form for a shed and the form for a fence each ask whether the property pins have been located. A pin is the marker that fixes a corner of the lot. If you cannot find yours, a surveyor can set them again.

On timing, the city's applications page gives three plain instructions. Approval takes a day or two. You should apply one week before starting any work. And payment is by check or cash when the application is dropped off. The same page tells applicants to contact City Hall for current fees because they are subject to change. That caution applies to the fee figures in this guide as well. The fee sheet the city posts carries no printed date, so treat the numbers here as what the sheet said on the day this guide was written, and confirm them with City Hall before you write a check.

Fences and sheds: the numbers on the forms

Start with the fence, because the city's fence application carries more rules than any other form in the set. The fee is eighty dollars for a new or replacement fence. The application must come with a survey or a shop drawing showing the location and dimensions of the fence on the lot.

The height rule has a split in it. In residential areas, a fence cannot be over six feet tall in the side and rear yards. In front yards the picture changes. The application says no fences are allowed in a front yard without written permission from the Community Services Committee. The guidelines sheet attached to the form puts a number on that case: four feet maximum in a front yard, and only with the committee's written approval. So a front-yard fence is not simply a lower fence. It is a fence that needs a separate approval before the permit means anything.

Where the fence goes is its own list. Fences can be placed up to the property line, and the application says a fence must be erected on or within the property lines and may not extend onto any public right of way. The guidelines also say the finished face has to point outward. The flush side of the fence faces away from the property, with the posts on the inside and the boards or fence material on the outside.

Several limits come from what sits under or across the yard rather than from the fence itself:

  • No fence may be built inside a drainage easement or a dedicated detention area.
  • A fence may not block the natural flow of storm water runoff. If a swale crosses a fenced area, you have to leave room for water to pass under the fence.
  • A fence may stand in a utility easement, but the utility companies can remove it when they need to work there, and the city says it would not be reinstalled. The yard must also stay accessible for that maintenance.
  • Call J.U.L.I.E. at 1-800-892-0123 before any digging, so buried utilities are located first.

On a lot with an easement, the third item is the one to read twice. The city is not forbidding the fence there. It is saying the fence can be taken down for maintenance and will not be put back.

Materials are limited too. The guidelines allow chain link, wood, PVC, plastic, wrought iron and other materials the city approves. Barbed wire, woven wire, slatted snow fence and T posts are not permitted in residential districts. Every chain link fence needs top rails. Two inspections apply to a fence, a setback inspection to verify where it sits and a final inspection when it is finished, and the form asks you to call at least 24 hours ahead.

Now the shed. The city treats a shed and a detached garage under one application, and the fee works on a sliding line at 100 square feet. A structure of 100 square feet or less carries no fee on the application form. Over 100 square feet, the fee is twenty-five cents per square foot with a fifty dollar minimum, and the fee sheet adds that mechanical inspections are charged as the building and zoning administrator requires. If the shed has electric service, the code adds an inspection at eighty dollars.

The real substance is the accessory building code, section 17.20.080, which the form prints in full. It has six rules, and each one is a number or a yes-or-no:

  • There must be a principal building on the lot. A shed cannot go on an empty lot.
  • The structure cannot exceed fifteen feet in height, measured from the peak to the ground.
  • It must sit at least ten feet from the principal building. The code gives the reason as fire code regulations.
  • It must sit at least six feet from the side and rear lot lines.
  • It cannot be built in an easement area or a drainage area.
  • Electric to the building requires an additional inspection.

Put those numbers together and you can test a backyard on paper. Take a shed that is ten feet deep. Where the lot gives you a rear yard of twenty feet from the back of the house to the back line, the shed has to clear the house by ten feet and the rear line by six. That is sixteen feet of required clearance across the depth of the yard before the shed itself is counted. A twenty-foot yard does not leave room for a ten-foot-deep shed. This is arithmetic from the city's own form, not a ruling on any lot, and the survey is what settles it. But it shows why the city asks for setback dimensions on the front, rear and sides before it issues the permit.

The shed form also asks one question that deserves attention in a river town. It asks whether the proposed structure sits in a floodplain or a detention area. A yes changes which rules apply, and we cover that side of Byron in our guide to Byron flood zones and Ogle County flood rules.

Pools, hot tubs and decks

A pool or hot tub permit in Byron is one permit with three prices. The fee sheet lists an above-ground pool at eighty dollars, an in-ground pool at one hundred seventy-five dollars, and a hot tub or spa at eighty dollars. A note on the sheet says all swimming pool and hot tub permits include an electrical inspection. That is worth knowing, because the shed code charges separately for the same inspection.

The application asks for more technical detail than the fence or shed form. You give the length, width and depth, the shape, the water capacity in gallons, whether the pool is entirely above ground and its height above ground, and the make, model and capacity of the filtering system. You also attach a sketch that shows the lot layout, every building on the lot, and the distances from the pool or spa to the back and side lot lines. The form says a pool, hot tub or spa must be placed at least six feet from any lot line.

The enclosure rules live in the city code, chapter 8.58, and the application attaches them. The code defines a private swimming pool as a manmade rigid or semi-rigid receptacle for water deeper than twenty-four inches at any point, used for swimming, wading or bathing, in the ground or above it, and used only by the owner or occupant and guests. A shallow wading pool under that depth falls outside the definition. Anything deeper falls inside it.

For a pool inside the definition, the code says the owner must maintain a fence all the way around it. The fence has to be at least four feet high, with no gap or opening larger than six inches other than doors or gates. Every way in must be locked when the pool is not in use. Any gate or door through the fence needs a self-closing and self-latching device mounted at the top. A door of the dwelling itself can form part of the enclosure and does not need that device.

Above-ground pools get a specific allowance. If you rely on the wall, the code adds two conditions. The ladder must be lockable and locked when the pool is not in use, or removable and removed. And the deck around the pool must have a lockable gate that stays locked when the pool is not in use.

Hot tubs are handled in one sentence. An outdoor hot tub or spa must be enclosed by a fence meeting the same fence and gate standards, or it must be covered with a locked lid or cover when it is not in use. The lid is the simpler route for a tub on a patio. It also means a hot tub does not require a full perimeter fence if the cover locks.

Decks come with the longest list of numbers of any project on the city's forms. The fee is eighty dollars for a deck or porch without a roof. A porch with a roof is priced like a shed, at twenty-five cents a square foot with a fifty dollar minimum. The deck application lists what the inspector will look for:

  • Postholes at least 42 inches deep. The specifications sheet adds that piers must be at least 8 inches across if round or 10 inches if square.
  • Stairways not less than 36 inches wide at every point, with a riser no taller than 7-3/4 inches and treads at least 11 inches deep.
  • Guardrails on any deck 30 inches or more above grade, with less than 4 inches between spindles.
  • Handrails between 34 and 38 inches high.
  • Posts that are pressure treated or water resistant, and galvanized metal post-to-beam connectors.
  • Floor joists at a maximum of 16 inch centers when using 5/4 decking, rated for a 40 pound per square foot live load.

Two inspections are tied to the build sequence. The first is the pier inspection, after the holes are dug and before concrete is poured. The second is the final inspection after the deck is complete. The form asks you to call 24 hours ahead for the posthole inspection. The order is the point. If concrete goes into the holes before the inspector has looked, the hole depth can no longer be seen.

The deck form also carries a warning for anyone who pulls the permit in their own name for a contractor. It says that if you obtain the permit on behalf of a contractor, you are liable for all work, including any violations or incomplete work. The name on the permit is the name that answers for it.

Finally, the specifications sheet says the location of the deck on the property must meet all zoning requirements, and the form notes that other requirements apply for corner lots. The city does not spell out the corner-lot requirements on the form, so that is a question for the building inspector before you draw the plan.

Outside the city limits: Ogle County and the unincorporated areas

Not every Byron address is inside the city. The City of Byron posts a map of its corporate limits on its website, and it directs address questions to City Hall at 815-234-2762. The reason to check is that the permit office changes with the boundary. Ogle County's Planning & Zoning Department regulates construction only in the unincorporated area. Its FAQ says that its jurisdiction does not include land within incorporated cities and villages, and that a project inside a city or village goes to that city or village.

The county's system uses different words and different rules. Ogle County has not adopted a uniform building code, so what people call a building permit is called a Zoning Certificate there. A Zoning Certificate is required before construction of decks, patios, sheds, gazebos, garages, storage buildings and other accessory structures, along with dwellings and additions. The county says to allow a day or two for processing.

A swimming pool is covered when its design capacity is 5,000 gallons or more. That threshold is the county's, and it is a different test from the city's depth-based definition. A smaller pool might fall outside the county's requirement and inside the city's code, depending on which side of the line the house is on.

Fences are where the two systems split sharply. The county's FAQ says its zoning ordinance has no fence regulations, so a fence does not need a Zoning Certificate, with two exceptions. A fence in a designated floodway, or in an unmarked "A" zone on the county's flood maps, needs a Floodplain Development Permit first. And a fence at a road or street intersection has to respect the sight distance triangle, which keeps anything from impeding vision between 2 feet and 8 feet above grade within the triangle formed by the right-of-way lines and points 40 feet from their intersection. In Byron city limits a fence needs a permit and a height limit. In unincorporated Ogle County it does not, apart from those two cases.

The county FAQ also notes that re-roofing, window replacement and siding replacement generally do not need a permit. That is another point where the city's list is stricter. The city lists re-roofing as a permit item.

Inspections in the county are zoning inspections, not building inspections. The FAQ describes three: a stake-out inspection at the start, a footings inspection, and a final inspection that results in an Occupancy Certificate. To prepare for the first, you place stakes or paint where the structure will go, mark every lot line, and locate and mark the septic components. The county asks for the septic components to be marked at that stage, along with the lot lines.

One more layer sits outside both city and county. Many subdivisions carry private covenants and deed restrictions. The county says plainly that it does not enforce them, because they are agreements between property owners. Its advice is to get the subdivision covenants, the recorded deed or other documents, and to check with a homeowner's association if there is one, before adding a shed or a fence. Because those are private agreements the county does not enforce, the documents themselves are the place to look.

On enforcement, the county says it starts with written notice of the violation, or a spoken notice for a minor problem that is easy to fix, and that a firmer written order follows if that fails. Unresolved cases can go to the Ogle County Code Hearing Unit or to Circuit Court. The Planning & Zoning office is at 911 Pines Road in Oregon, and its number is 815-732-1190. It is open Monday through Friday from 8:30 to 4:30.

Two related guides cover other parts of owning in Byron. Our guide to Byron property taxes and your Ogle County bill covers the bill, and our guide to moving to Byron: water, sewer, trash and utilities covers who to call after closing.

Bottom line

Inside the City of Byron, a fence, shed, pool, hot tub or deck needs a permit first, a survey or lot drawing with distances to the lot lines, and an inspection or two on the way. The city's forms contain the real numbers: six feet for a side or rear fence, fifteen feet for a shed's height, ten feet from the house, six feet from the side and rear lines, a four-foot enclosure around a pool, and 42 inches for deck postholes. Outside the city limits, the county asks for a Zoning Certificate on decks, sheds and larger pools and has no fence permit at all, but private covenants can still apply.

Before you buy, ask whether the structures on the lot were permitted, check the corporate limits map to see which office applies, and read any subdivision covenants. Then confirm the figures here with the City of Byron building inspector or Ogle County Planning & Zoning, since the city says its fees can change. When you are ready to look at homes for sale in Byron, Gambino Realtors has been in business since 1923, and our full Illinois real estate guide lists every article in this series.

Before you dig, build or buy, these are the permit questions worth settling first.

Frequently Asked Questions

Does a fence need a permit in the City of Byron?

Yes. The City of Byron lists fences among the projects that need a building permit before work starts, and its fence application carries an eighty dollar fee. You attach a survey or shop drawing showing where the fence sits and how long and tall it is. A side or rear fence in a residential area cannot be over six feet. A front-yard fence needs written permission from the Community Services Committee, and the guidelines cap it at four feet.

How close to the lot line can a shed be built in Byron?

Section 17.20.080 of the city code says an accessory building must be at least six feet from the side and rear lot lines and at least ten feet from the principal building, which the form attributes to fire code regulations. It also cannot be taller than fifteen feet from peak to ground, cannot go in an easement or drainage area, and needs a principal building on the lot. The form asks for setback dimensions on the front, rear and sides.

Is there a fee for a small shed in Byron?

The shed and detached garage application lists no fee for a structure of 100 square feet or less. Over 100 square feet, the fee is twenty-five cents per square foot with a fifty dollar minimum, and the fee sheet adds that mechanical inspections are charged as required. If electric service runs to the building, the city code adds an additional inspection at eighty dollars. The city says fees can change, so confirm them with City Hall.

What does Byron require around a swimming pool?

For a private pool deeper than twenty-four inches, city code chapter 8.58 requires a fence that completely surrounds the pool, at least four feet high, with no opening larger than six inches other than doors or gates. Gates need self-closing and self-latching devices at the top, and every entry must be locked when the pool is not in use. The permit application also says the pool must sit at least six feet from any lot line.

Does a hot tub in Byron need a fence?

Under the city code, an outdoor hot tub or spa must be enclosed by a fence that meets the pool fence and gate standards, or it must be covered with a locked lid or cover whenever it is not in use. A hot tub also needs its own permit. The fee sheet lists it at eighty dollars and says all pool and hot tub permits include an electrical inspection.

What inspections does a deck need in Byron?

The deck specifications list two inspections. The first is the pier inspection, after the holes are dug and before concrete is poured. The second is the final inspection once the deck is complete. The form asks you to call 24 hours ahead for the posthole inspection. Postholes must be at least 42 inches deep, and a guardrail is required on any deck 30 inches or more above grade.

I am outside the Byron city limits. Do I still need a fence permit?

Not from Ogle County, with two exceptions. The county zoning ordinance has no fence regulations, so a fence does not need a Zoning Certificate. A fence in a designated floodway or an unmarked "A" zone needs a Floodplain Development Permit, and a fence at a road or street intersection must keep the sight distance triangle clear. Private subdivision covenants can still apply, and the county does not enforce them.

How do I find out whether an address is inside the City of Byron?

The City of Byron posts a map of its corporate limits on its website under City Limits, and it directs questions about an address to City Hall at 815-234-2762. The answer decides which office issues the permit. Inside the city, you apply at Byron City Hall. In the unincorporated area, you contact Ogle County Planning & Zoning at 815-732-1190, which says it does not have jurisdiction inside incorporated cities and villages.

Login to My Homefinder