Ogle County's hazard plan names exactly one stream as a flood source for the Village of Stillman Valley, and it is Stillman Creek, not the Kyte River. The same plan counts two residential structures inside the village's base floodplain, and it records that the village joined the National Flood Insurance Program on July 25, 2016, just over three weeks before the current FEMA map took effect on August 17, 2016.
If you are comparing homes for sale in Stillman Valley, this guide lays out what the public record says about flood risk and where it goes quiet. Gambino Realtors has been in business since 1923 and is based in Rockford. Everything below comes from FEMA's Flood Insurance Study for Ogle County, the county's hazard mitigation plan, the county's flood ordinance and planning pages, FEMA's FloodSmart site and the state's seller disclosure form, all read in October 2026. The village's own flood ordinance could not be found online, and the guide says so where that matters.
The Kyte River is one of the named rivers in Ogle County's flood documents, so it is fair to ask whether it matters here. The county's flood page names the Rock, Kishwaukee, Kyte and Leaf Rivers as examples of riverine systems in the county. It says their floodplains typically flood in spring or summer and are subject to periodic flooding from excessive rainfall, ice jams or debris jams. FEMA's study describes the Kyte as a tributary of the Rock River that drains 30 square miles and flows south and southwest along the eastern edge and southern portion of Rochelle. The county plan lists the Kyte River as a flooding water body for Hillcrest, for Rochelle and for the unincorporated county. For Stillman Valley the plan lists a single name, Stillman Creek.
That gives a buyer a plain starting point. The county's own table points to Stillman Creek for the village. Both streams sit on the same FEMA map. The countywide Flood Insurance Rate Map dated August 17, 2016 covers the Kyte River, Stillman Creek and the Rock River together, and the 2016 revision added new analyses of the Kyte River watershed and of the Rock River.
Stillman Creek is a studied stream in that FEMA report. FEMA's detailed analysis, the kind that produces numbered base flood elevations, covers the creek from its confluence with the Rock River to approximately 24,900 feet upstream, at County Highway 4, which the study also calls Stillman Road. At the Rock River confluence, FEMA records a drainage area of 61.2 square miles and a flow of 6,740 cubic feet per second for the one-percent-annual-chance flood. The floodway table for the creek runs through ten cross sections, lettered A to J, from 1,700 feet to 21,660 feet above the confluence. For the 2016 revision, FEMA also applied the backwater effects from its new Rock River study to Stillman Creek and to Mill Creek.
What the study does not do is tie that studied reach to village streets. The published text gives distances from the Rock River, not street names or lot lines, so the only way to learn whether an address touches the mapped creek is to look the address up on the map itself. The county's flood page lists four places to do that: FEMA's Map Service Center, the Illinois Department of Natural Resources flood maps, Ogle County GIS and FEMA's National Flood Hazard Layer for Google Earth.
The plan puts a number on the village. Its table of existing residential structures located within a base floodplain, prepared by Ogle County GIS from the effective flood maps, shows two for Stillman Valley. The plan's 2010 figures for the village are a total area of 0.543 square miles and 447 housing units, so the count is two structures in a village of a little over half a square mile. The plan also says that Hillcrest, Leaf River, Oregon, Rochelle and Stillman Valley are susceptible to riverine flooding because of their proximity to floodplains.
For its dollar-loss estimates the plan makes a scenario assumption. It assumes Stillman Creek overflows its banks and floods the northern edges of the village. That is a planning scenario and not a forecast. The plan's list of verified flash flood events by jurisdiction, covering 1996 to 2017, has no entry for Stillman Valley. The plan is just as clear about the limit of such a list. It records that county and municipal officials have reported overland flood issues outside the base floodplain, that this overland flooding is known to impair travel, and that only 4.6 percent of the county's land lies within the base floodplain while nearly the entire county is vulnerable to flash flooding. It does not single out Stillman Valley. FEMA's own map notes add that the map "may not identify all areas subject to flooding, particularly from local drainage sources of small size."
One property-level fact from the plan is worth knowing. In 2018 the village completed a new wastewater treatment plant with a capacity of 200,000 gallons per day, built north of town and, in the plan's words, outside the 100-year floodplain. The plan lists the project among the village's completed mitigation actions.
Ogle County adopted its current Flood Damage Prevention Ordinance as Ordinance O-2016-0505 on May 17, 2016, effective August 17, 2016, the same day the current FEMA map took effect. It sits in Chapter 16, Division 10 of the county code. The first thing to read in it is who it covers. The ordinance names the county Planning and Zoning Administrator as the Floodplain Administrator for floodplains within the county but outside the boundaries of any incorporated city or village. Stillman Valley is an incorporated village. By its own terms, then, the county administrator's job covers land outside village limits.
The plan says the village has its own floodplain zoning ordinance, adopted in 2016 according to its participation table. That table lists the village's NFIP participation date as July 25, 2016 and its Community Rating System participation as no. The text of the village's ordinance is not something this guide could read, because the village's website could not be reached and no copy turned up on the county's pages. The plan also lists, as actions for the Village Board, making the newest flood maps available at the Village Clerk's office and making village officials aware of the maps and of construction in a floodplain. Those entries carry the status "new," so they read as intentions and not as proof of a counter service.
That leaves a careful reading of the county ordinance. It is not a quotation of the village code. If you are under contract on a Stillman Valley property that touches a mapped floodplain, ask the village for its ordinance in writing and ask what it requires before any permit.
Here is how the county ordinance works. It starts with the base flood, defined as the flood with a one percent chance of being equaled or exceeded in any given year, also known as the 100-year flood. The standard for buildings is the flood protection elevation, which is the base flood elevation plus one foot of freeboard. The ordinance explains freeboard as a margin for uncertainties in calculations, future watershed development, unknown localized conditions, wave action and ice or debris jams. FEMA's study puts the one-percent label in perspective. It says the risk of a one-percent flood in any 50-year period is approximately 40 percent, and over 90 years approximately 60 percent. Run the same arithmetic over a 30-year mortgage and the chance of at least one such flood is about one in four.
The floodway and base flood elevation for a list of named streams, which includes the Kyte River, the Kyte River Overflow, the Rock River and Stillman Creek, come straight from the August 17, 2016 map and study. For any other floodplain the ordinance falls back on the best available data. If you disagree with the data, the ordinance puts the burden on you. The disagreeing party pays for the detailed engineering study and submits it to FEMA and to the Illinois Department of Natural Resources, Office of Water Resources, for approval before developing the site.
The ordinance also looks past the printed map. When someone applies for a permit, the administrator compares the site elevation with the base flood elevation. Development on land below the base flood elevation and hydraulically connected to a flood source is covered even if the current map does not show it as floodplain. Land that survey data shows to be higher than the base flood elevation, and that has not been filled since the date of the site's first flood map, is outside the floodplain and outside the ordinance. The county page says the same thing in plainer terms. If there is uncertainty about whether a property is subject, the applicant must provide certified information on the elevation of the site in relation to the 100-year floodplain boundaries.
The word that triggers a permit is development, and the definition is wide. The ordinance defines it as any man-made change to real estate, and lists demolition, construction, reconstruction, repair, placement of a building, structural alteration, utilities, roads, levees, walls or fences, filling, grading, excavating, paving and the storage of materials, including gas and liquid storage tanks. Routine maintenance of existing buildings, resurfacing roads, gardening and plowing are left out. The county itself calls the ordinance "fairly restrictive" and says it allows only limited development activity without variation.
Building rules apply once the work passes certain thresholds. The protection standard applies to a new building, or an alteration or addition, valued at more than one thousand dollars or 70 square feet. It also applies to a substantial improvement, which is work that costs half or more of the building's market value before the work starts, or that increases the floor area by more than 20 percent. The ordinance counts these cumulatively since May 20, 2003, and treats the first alteration of any wall, ceiling, floor or structural part as the start. Projects needed only to fix an existing health, sanitary or safety code problem are excluded, as are alterations to structures on the National or Illinois Register of Historic Places. Substantial damage works the same way at the same fifty percent, and a building that is substantially damaged must be brought entirely into compliance within 24 months of the damage.
The ordinance offers three ways to meet the standard. Permanent fill must bring the lowest floor, basement included, to or above the flood protection elevation, with the fill placed in layers no greater than six inches before compaction, extending at least ten feet beyond the foundation, protected against erosion and made of rock or soil only. A raised building may stand on stilts, piles, walls, a crawlspace or a foundation permanently open to floodwaters, with the lowest floor and the electrical, heating, ventilating, plumbing and air conditioning equipment and utility meters at or above the flood protection elevation. Enclosed areas below that level need at least two flood openings, one on each wall within one foot of grade, with one square inch of opening for each square foot of enclosed area, unless an engineer certifies the design. The third path is a crawlspace below the flood protection elevation, which must be anchored, have flood openings, sit no more than two feet below the adjacent exterior grade on the inside, measure no more than four feet tall inside, and have drainage and flood-resistant materials and utilities above the flood protection elevation.
A non-residential building has one more option, dry floodproofing, with a licensed engineer or architect certifying that the structure is watertight below the flood protection elevation and works without human intervention or outside electricity. Levees, berms and floodwalls do not count as floodproofing. A manufactured home or travel trailer that is permanently installed must be raised and anchored under the Illinois Mobile Home Tie-Down Act rules, and a recreational vehicle that stays on a site more than 180 days a year faces the same standard unless it meets a list of conditions.
A garage or shed that is accessory to an existing residential use can be permitted if it is not habitable, holds only vehicles and tools, sits outside the floodway or has the needed state and federal permits, and has flood openings on each wall within one foot of grade. It must also be anchored, use flood-resistant materials below the base flood elevation, keep utilities above the flood protection elevation and store flammable or toxic materials above that level. The size limit is 576 square feet, which is 24 feet by 24 feet. The printed ordinance gives its value limit two ways in the same sentence, ten thousand dollars in words and fifteen thousand in figures, so ask the department which figure it applies before you plan a build.
The penalty provisions matter to a buyer because a notice of violation can be recorded on the title. After ten days of written notice without a fix, the county may seek an injunction, the fine runs from fifty to five hundred dollars, each week is a separate offense and the county may record a notice of violation on the title. The administrator must also tell the owner that the violation may cause the standard flood insurance policy to be suspended. A stop-work order is issued in writing. In the ordinance's own disclaimer, larger floods may occur than the standard assumes, and nothing in the rule promises that development inside or outside the floodplain will be free from flooding or damage.
Flood insurance is available through the National Flood Insurance Program where the community participates, and the county's hazard plan shows Stillman Valley as a participant since July 25, 2016. FloodSmart says flood insurance is required if you own a home in a Special Flood Hazard Area and have a government-backed mortgage, and that some banks require it even outside high-risk areas. Homeowners insurance does not fulfill that mortgage requirement. The county's flood page adds that flood losses are not typically covered under renter and homeowner policies.
There is also a rule that follows the property. FEMA says that if a property has received federal disaster assistance before, flood insurance is required to qualify for future assistance, and that this requirement is tied to the property and not to an individual homeowner. A buyer who purchases a house that once received disaster aid inherits that requirement.
Timing matters. FloodSmart says a new policy goes into effect 30 days after purchase, with exceptions, including no wait when the policy is bought while making, increasing, extending or renewing a mortgage. The county's flood page also tells readers not to delay, and notes that flood insurance is available whether the building is inside or outside an identified flood-prone area. FEMA adds that over the past 10 years, nearly one-third of National Flood Insurance Program claims came from outside the high-risk zones.
On cost, FEMA's page gives no figure for any village. It says the rate comes from where the property is built, how it is built and what it would cost to replace, and that every provider offers the same rates. Homeowner building coverage runs up to two hundred fifty thousand dollars and contents coverage up to one hundred thousand dollars. An elevation certificate is the document that records a building's height against expected floodwater. FEMA says it can identify discounts but does not set the rate, and that a homeowner does not need one to buy a policy unless the property is in a high-risk Zone A or V. You can ask the village or the county whether one is on file. If none exists, a land surveyor, engineer or architect prepares it.
A discount deserves a careful reading. The county's January 2019 progress report says Ogle County entered the Community Rating System in 2015 as a Class 7 community and that its work earns a 15 percent premium discount for policies in Special Flood Hazard Areas within unincorporated Ogle County. The plan's participation table lists the Village of Stillman Valley's Community Rating System participation as no. A discount earned by the county for unincorporated land is not a statement about a village address, so ask the insurance agent what applies to the specific property.
The same split shows up in the county's map service. The Flood Map Information Service at Ogle County Planning and Zoning will tell you whether a property is inside or outside a Special Flood Hazard Area, and it will provide the zone, the base flood elevation if shown, flood depth data and historical flooding information. The county describes that service as answering for the current map for unincorporated Ogle County. It has copies of Letters of Map Amendment and Letters of Map Revision on file. For a village address, the village clerk's office or FEMA's Map Service Center is the first stop. There is no charge. The office is at 911 Pines Road in Oregon, takes calls at (815) 732-1190 from 8:30 a.m. to 4:30 p.m. Monday through Friday, and asks for the address and the property index number.
FEMA sorts every address into a zone. Zones A, AE, AH, AO, AR and A99 are the high-risk areas. Zone B and shaded Zone X are moderate, between the limits of the 100-year and 500-year floods. Zone C and unshaded Zone X are lower risk but, in FEMA's words, not entirely without risk. Zone D means the risk has not been analyzed and does not mean no risk. If you believe a property was wrongly included in a Special Flood Hazard Area, the county explains that an owner may apply to FEMA for a formal determination. If FEMA grants it, the owner can send the Determination Document to the lender and ask for the federal flood insurance requirement to be removed.
The Illinois Residential Real Property Disclosure Report puts flooding in front of the buyer before a contract. Item 2 asks whether the seller currently has flood hazard insurance on the property. Item 3 asks whether the seller is aware of flooding or recurring leakage problems in the crawl space or basement. Item 4 asks whether the seller is aware that the property is located in a floodplain. The form defines aware as actual notice or actual knowledge without any specific investigation or inquiry. That wording means a seller answers from what he or she knows, so the form is a starting point and not a map check. A yes or not applicable on items 2 through 4 requires an explanation from the seller. The Illinois seller disclosure report guide walks through the whole form.
The Stillman Valley property tax guide breaks down what is on an Ogle County bill. For a nearby city in the same county whose flood ordinance could be read in full, the Byron flood zones guide walks through the Rock River and the county rules, and the Illinois Real Estate Guide lists every article Gambino has published.
For Stillman Valley, the county's record points to Stillman Creek, not the Kyte River, and to a count of two mapped residential structures in the plan. That is a fact about the 2016 map and a 2018 plan, not about any one street. The map does not catch every drainage problem, the village's own ordinance is the rule that governs inside village limits, and a Special Flood Hazard Area designation is what drives the lender's insurance requirement.
Before you make an offer on a Stillman Valley home for sale, put three questions to the right offices. Ask the village whether the address is in a mapped flood zone and what its ordinance requires for any planned work. Ask the lender whether flood insurance will be required. Ask an insurance agent for a quote before the 30-day wait becomes a closing problem. Then read the seller's disclosure items 2, 3 and 4 against what the map says. None of this is legal, tax or financial advice, and each office named here is the one that can confirm the rule for a particular address.
Here are short answers to the questions a buyer can settle from the public record before making an offer.
Ogle County's hazard plan does not list the Kyte River for Stillman Valley. Its table of bodies of water subject to flooding gives the Kyte River for Hillcrest, Rochelle and the unincorporated county, and gives Stillman Creek as the only entry for Stillman Valley. The Kyte River does appear on the county flood page as one of the riverine systems in Ogle County. For a specific address, check the current FEMA map, because the plan names streams for the village as a whole and not for individual lots.
FEMA's Ogle County study includes Stillman Creek as a detailed-study stream. The detailed analysis runs from the creek's confluence with the Rock River to approximately 24,900 feet upstream at County Highway 4, also called Stillman Road. The study gives a drainage area of 61.2 square miles at the confluence and publishes floodway data at ten cross sections. It does not tie those distances to village street addresses, so the map is the way to check an address.
The ordinance makes the county Planning and Zoning Administrator the Floodplain Administrator for floodplains inside the county but outside any incorporated city or village. Stillman Valley is a village, so floodplain permits inside the village limits are a village matter. The county plan says the village has a floodplain zoning ordinance, adopted in 2016. Ask the village for its text, because this guide could not read it online.
The county's hazard plan counts two existing residential structures located within a base floodplain in Stillman Valley. Ogle County GIS prepared the count from the effective flood maps. The plan is dated December 2018 and the village had 447 housing units in the plan's 2010 figures. A count in a plan is not a map check for a specific address, and it does not cover flooding from local drainage outside the mapped floodplain.
FEMA says flood insurance is required if you own a home in a Special Flood Hazard Area and have a government-backed mortgage, and that some banks require it even outside high-risk areas. Whether a given address is in that area depends on the map, so ask the lender what it will require for that address. FEMA also says homeowners insurance does not fulfill the mortgage requirement. A new policy takes effect 30 days after purchase unless an exception applies, such as buying while making or renewing a mortgage.
The Residential Real Property Disclosure Report has three flooding items. Item 2 asks whether the seller currently has flood hazard insurance. Item 3 asks whether the seller is aware of flooding or recurring leakage problems in the crawl space or basement. Item 4 asks whether the seller is aware that the property is located in a floodplain. Aware means actual notice or actual knowledge without any specific investigation. A yes or not applicable answer on these items requires an explanation from the seller.
The ordinance defines development as any man-made change to real estate. It lists demolition, construction, reconstruction, repair, placing a building, structural alteration, utilities, roads, levees, walls or fences, filling, grading, excavating, paving and storing materials. Routine maintenance, road resurfacing, gardening and plowing are excluded. Inside the county's own jurisdiction a development permit comes first. In the village, the village ordinance governs, so confirm its definition with the village.